Wika IPT-11 Manuale Utente

Operating InstructionsProcess pressure transmitter IPT-1* Vers. 3.0 - metalicsensor4 … 20 mA/HART

4 Mounting4.1 General instructionsMake sure that all parts of the instrument in contact with the measuredproduct, especially the sensor element, proce

The ventilation of the measuring cell is realised by a filter element inthe socket of the electronics housing. The ventilation of the electronicshousin

Danger:Instruments in the version "Oil and grease free for oxygen" should beunpacked just before mounting. After the protective cover of the

5 Connecting to power supply5.1 Preparing the connectionAlways keep in mind the following safety instructions:l Connect only in the complete absence o

Take note of the corresponding installation regulations for Exapplications. In particular, make sure that no potential equalisationcurrents flow over t

9 Check the hold of the wires in the terminals by lightly pu lling onthem10 Connect the screen to the internal ground terminal, connect theouter groun

I²CDisplay1 2 5 6 7 83412Fig. 7: Electronics and connection compartment, single chamber housing1 Plug connector for service2 Spring-loaded terminals f

5.4 Wiring plan, double chamber housing1 2 345Fig. 9: Double chamber housing1 Housing cover, connection compartment2 Blind stopper or plug M12 x 1 for

312Display1 2I²CFig. 11: Connection compartment, double chamber housing1 Plug connector for service2 Ground terminal for connection of the cable scree

5.5 Wiring plan double chamber housing Ex d1 2 345Fig. 13: Double chamber housing1 Housing cover, connection compartment2 Blind stopper or plug M12 x

Contents1 About this document1.1 Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41.2 Target group . . . . . . . . . . . .

121 2Fig. 15: Connection compartment double chamber housing Ex d1 Spring-loaded terminals for power supply and cable screen2 Ground terminal for conne

Then the corresponding current is outputted to the cable (the valuecorresponds to the actual level as well as the settings already carriedout, e.g. fa

6 Set up with the indicating and adjustmentmodule6.1 Short descriptionThe indicating and adjustment module is used for measured valuedisplay, adjustme

Fig. 17: Mounting the indicating and adjustment moduleNote:If you intend to retrofit the instrument with an indicating and adjustmentmodule for continu

6.3 Adjustment system1.1231Fig. 18: Indicating and adjustment elements1 LC display2 Indication of the menu item number3 Adjustment keysl [OK] key:- Mo

6.4 Setup procedureIn HART-Multidrop mode (several sensors on one input) the addressmust be set before continuing with the parameter adjustment. You w

To select the adjustment unit (in the example switching over from barto mbar) you have to proceed as follows:4)1 Push the [OK] button in the measured

Unit of measurementDensity0001000kg/dm³6 Enter the requested density value with [->] and [+], confirm with[OK] and move to position correction with

5 Confirm with [+] and move to max. adjustment with [->].The min. adjustment is finished.Information:For an adjustment with filling, you simply enter

The position correction compensates the influence of the mountingposition or static pressure on the measurement. It does not influencethe adjustment val

8 Maintenance and fault rectification8.1 Maintenance, cleaning . . . . . . . . . . . . . . . . . . . . . . .398.2 Remove interferences . . . . . . . .

▶Basic adjustmentDisplayDiagnosticsServiceInfo2 Confirm the menu "Basic adjustment" with [OK], the menu item"Unit" will be displaye

Proceed as follows:1 Edit the mbar value in the menu item "zero" with [OK].Zero adjustment000.0 %P=+0000.0 mbar0000.0 mbar2 Set the requeste

This f unction enables reading out parameter adjustment data as wellas writing parameter adjustment data into the sensor via the indicatingand adjustm

Menu section Function Reset valueScaling 0.00 to 100.0Decimal point indication 8888.8Service Current output - characteristics 4 … 20 mACurrent output

6.5 Menu schematicInformation:Depending on the version and application, the highlighted menuwindows are not always available.Basic adjustment1▶Basic a

Diagnostics3Basic adjustmentDisplay▶DiagnosticsServiceInfo3.1Pointerp-min.: -5.8 mbarp-max.: 167.5 mbarT-min.: -12.5 °CT-max.: +85.5 °C3.2Sensor statu

6.6 Saving the parameter adjustment dataIt is recommended noting the adjusted data, e.g. in this operatinginstructions manual and archive them afterwa

7 Setup with PACTware and other adjustmentprograms7.1 Connecting the PC312~=Power supplyPACTwa re /DTMHART-ModemTMFig. 19: Connecting the PC to th

Note:Keep in mind that for setup of IPT-1*, DTM-Collection in the actualversion must be used.All currently available WIKA DTMs are provided in the DTM

8 Maintenance and fault rectification8.1 Maintenance, cleaningWhen used in the correct way, no special maintenance is required innormal operation.In so

1 About this document1.1 FunctionThis operating instructions manual provides all the information youneed for mounting, connection and setup as well as

l No power supplyà Check cables for breaks; repair if necessaryl Operating voltage too low or load resistance too highà Check, adapt if necessary? Cur

By doing this you help us carry out the repair quickly and withouthaving to call back for needed information.Process pressure transmitter IPT-1* Vers.

9 Dismounting9.1 Dismounting stepsWarning:Before dismounting, be aware of dangerous process conditions suchas e.g. pressure in the vessel, high temper

10 Supplement10.1 Technical dataGeneral dataPressure type Gauge pressure or gauge pressureMeasuring principle- Measuring ranges ≤ 16 bar piezoresistiv

Fulfilled NAMUR recommendations NE 43Dynamic behaviour outputRun-up time approx. 10 s90 %100 %10 %ttTAttS21Fig. 20: Sudden change of the process variab

Nominal range Overload, max. pressure Overload, min. pressure0 … 16 bar/0 … 1.6 MPa 80 bar/8 MPa -1 bar/-100 kPa0 … 40 bar/0 … 4 MPa 80 bar/8 MPa -1 b

Influence of the product or ambient temperatureApplies to instruments with digital signal output (HART, Profibus PA, Foundation Fieldbus) as wellas to i

Product temperature front-flush threaded fitting G1 A according to EHEDG, threaded fittingM44 x 1 .25 as well as hygienic fittings, depending on seal16) 1

Protection- unassembled IP 20- mounted into the sensor without cover IP 40Materials- Housing ABS- Inspection window Polyester foilPower supplyOperatin

Electrical protective measuresProtection- Housing, standard IP 66/IP 6721)Overvoltage category IIIProtection class IIFunctional safety (SIL)The functi

2 For your safety2.1 Authorised personnelMount and set up the pressure transmitter only if you know theapplicable national regulations and have the ap

10.2 DimensionsHousingM20x1,5M20x1,5/½ NPT234M20x1,5/½ NPT~ 69 mm(2 23/32")ø 77 mm(3 1/32")112 mm (4 13/32")M20x1,5/½ NPT1~ 69 mm(2 23/

IPT-1* - threaded fittingSW27SW2760°23mm(29/32")G ½ A63mm(2 31/64")57mm(2 1/4")15mm(19/32")3mm(1/8")ø 3mm (1/8")ø 6mm (15

IPT-1* - front-flush connection, part 1SW4120,5 mm(13/16")G1B G½B65 mm(2 9/16")ø 30 mm (1 3/16")SW6022 mm(55/64")SW2720,5 mm(13/16&

IPT-1* - front-flush connection, part 251 mm(2 1/64")ø 84 mm (3 5/16")RT RASA ø64 mm (2 33/64")82 mm(3 15/64")3T 3R ø 65 mm (2 9/

54 Process pressure transmitter IPT-1* Vers. 3.0 - metalic sensor • 4 … 20 mA/HART10 Supplement31543-EN-090130

Process pressure transmitter IPT-1* Vers. 3.0 - metalic sensor • 4 … 20 mA/HART 5510 Supplement31543-EN-090130

WIKA Alexander Wiegand GmbH & Co. KGAlexander-Wiegand-Straße 3063911 Klingenberg/GermanyPhone +49 9372 132295Fax +49 9372 132706e-mail: support-tr

2.5 Safety approval markings and safety tipsThe safety approval markings and safety tips on the device must beobserved.2.6 CE conformityThis d evice f

3 Product description3.1 ConfigurationThe scope of delivery encompasses:l IPT-1* process pressure transmitterl Documentation- this operating instructio

The type label contains the most important data for identification anduse of the instrument:l Sensor typel Article and serial number devicel Technical

3.4 Packaging, transport and storageYour instrument was protected by packaging during transport. Itscapacity to handle normal loads during transport i